Your Fuel System
by: Kevin Schappell
The fuel system feed your engine the gasoline/diesel it needs to run. If anyone of the parts in the system break down your engine will not run. Let's look at the major parts of the fuel system,
Fuel tank: Basically a holding tank for your fuel. When you fill up at a gas station the gas travels down the filler tube and into the tank. In the tank there is a sending unit, which tells the gas gauge how much gas is in the tank.
Fuel pump: On newer cars the fuel pump is usually installed in the fuel tank. Older cars have the fuel pump attached to the engine or on the frame rail between the tank and the engine. If the pump is in the tank or on the frame rail then it is electric and is run by your cars battery. Fuel pumps mounted to the engine use the motion of the engine to pump the fuel
Fuel filter: Clean fuel is critical to engine life and performance. Fuel injectors have tiny openings, which clog easily so filtering the fuel is the only way to prevent this. Filters can be before or after the fuel pump, sometimes both.
Fuel injectors: Most domestic cars after 1986 and earlier foreign cars came from the factory with fuel injection. Instead of a carburetor to mix the fuel and air, a computer controls when the fuel injectors open to let fuel into the engine. This has resulted in lower emissions and better fuel economy. The fuel injector is basically a tiny electric valve, which opens and closes with an electric signal. In the picture below you can see the injectors towards the outer part of the intake. By injecting the fuel close to the cylinder head the fuel stays atomized ( in tiny particles ) so it will burn better when ignited by the spark plug.
Carburetors: A carburetor takes the fuel and mixes it with air without computer intervention. While simple in operation, they tend to need frequent tuning and rebuilding. This is why most newer cars have done away with carburetors in favor of fuel injection.
Common Problems:
I would say the most common problem is a clogged fuel filter. Make sure you follow your manufacturers recommendations as to when you should change the fuel filter. This information should be in your owner’s manual. Symptoms include sputtering at high speeds or engine not starting at all. Always check the ignition system first, if that's ok then the next suspect is the fuel filter.
Next most common problem is the fuel pump failing. Most modern electric fuel pumps can be heard when you turn the key on. If you don't hear the pump running and your car will not start, it could be your fuel pump. The first thing a mechanic will check is the relay, which sends power to the pump. If this is operating correctly then the pump will have to be replaced.
Last but not least are dirty injectors. While the fuel filter does a good job of filtering the fuel, it's not perfect. Over time deposits and tiny particles lodge themselves in the injectors. This can clog and injector and prevent it from delivering the fuel the engine needs. It can also cause an injector to stick open and send too much fuel into the engine. A regular addition of fuel system cleaner like STP Injector Cleaner, or Techtron fuel system cleaner can help keep your injectors clean. Most gas stations, department stores and all automotive parts stores will have a good cleaner available. Add it to your empty tank right before you fill up and it will clean as you drive. I recommend doing this every 3 months to keep your injectors performing like new. Mechanics also offer a cleaning service where they actually disconnect the fuel line and flush cleaner through the engine. This is only necessary when you let your injectors get to a point where they can not be cleaned by a store-bought product. Regular use of a good in-tank cleaner will keep you from having to pay for this service.
Where do you buy your gas?
Believe it, or not, it can make a difference. Always buy from a well know national brand service station. Gas stations, which are not affiliated with one brand of gas, tend to get whatever is left at the end of the day from the delivery truck. One day them might get Texaco, and Exxon another. Also water mixed with gas will cause problems with your engine. The engine will not run right, plus the water will promote rust in the fuel system. I have experienced this when I purchased gas at some no-name gas stations. Your car will feel sluggish and sometimes refuse to run if there is enough water in the gas.
Octane rating tip!!!!
Putting super in the tank will not get you any more performance or gas mileage unless specifically recommended by your cars manufacturer. If your owners manual says put in 87 octane...... DO IT. You are throwing money out the window if you are filling up on Super or Premium and you only need Regular.
About The Author
Kevin Schappell maintains http://www.carbuyersclub.com where he gives advice on buying, selling, insurance, and financing. A mechanical engineer and car guy, Kevin has decided to spend his online time helping others learn about automobiles. To learn more about how your car works, Kevin has created http://www.mycarwizard.com.
kevin@schappell.com
This article was posted on December 23, 2004
Se afișează postările cu eticheta pump. Afișați toate postările
Se afișează postările cu eticheta pump. Afișați toate postările
duminică, 25 decembrie 2011
Auto And Trucks
The Cooling System
by: Kevin Schappell
The purpose of the engine's cooling system is to remove excess heat from the engine, to keep the engine operating at its most efficient temperature, and to get the engine up to the correct temperature as soon as possible after starting. Ideally, the cooling system keeps the engine running at its most efficient temperature no matter what the operating conditions are.
As fuel is burned in the engine, about one-third of the energy in the fuel is converted into power. Another third goes out the exhaust pipe unused, and the remaining third becomes heat energy.
A cooling system of some kind is necessary in any internal combustion engine. If no cooling system were provided, parts would melt from the heat of the burning fuel, and the pistons would expand so much they could not move in the cylinders (called "seize").
The cooling system of a water-cooled engine consists of: the engine's water jacket, a thermostat, a water pump, a radiator and radiator cap, a cooling fan (electric or belt-driven), hoses, the heater core, and usually an expansion (overflow) tank.
Fuel burning engines produce enormous amounts of heat; temperatures can reach up to 4,000 degrees F when the air-fuel mixture burns. However, normal operating temperature is about 2,000 degrees F. The cooling system removes about one-third of the heat produced in the combustion chamber.
The exhaust system takes away much of the heat, but parts of the engine, such as the cylinder walls, pistons, and cylinder head, absorb large amounts of the heat. If a part of the engine gets too hot, the oil film fails to protect it. This lack of lubrication can ruin the engine.
On the other hand, if an engine runs at too low a temperature, it is inefficient, the oil gets dirty (adding wear and subtracting horsepower), deposits form, and fuel mileage is poor-- not to mention exhaust emissions! For these reasons, the cooling system is designed to stay out of the action until the engine is warmed up.
There are two types of cooling systems; liquid cooling and air cooling. Most auto engines are cooled by the liquid type; air cooling is used more frequently for airplanes, motorcycles and lawnmowers.
Liquid cooled engines have passages for the liquid, or coolant, through the cylinder block and head. The coolant has to have indirect contact with such engine parts as the combustion chamber, the cylinder walls, and the valve seats and guides. Running through the passages in the engine heats the coolant (it absorbs the heat from the engine parts), and going through the radiator cools it. After getting "cool" again in the radiator, the coolant comes back through the engine. This business continues as long as the engine is running, with the coolant absorbing and removing the engine's heat, and the radiator cooling the coolant.
A cooling system pressure tester is used to check the pressure in the cooling system, which allows the mechanic to determine if the system has any slow leaks. The leak can then be found and fixed before it causes a major problem.
The above information is directly from the Auto Insight program which you can buy online from AutoEducation.com.
Common Problems:
Let's look at the common problems cars have with the cooling system.
Broken hose. Hoses wear out and can leak. Once the coolant has left the system it can no longer cool the engine and it overheats.
Broken fan belt. The water pump is driven by the engine through a belt. If the belt breaks the water pump can not turn and coolant will not be circulated through the engine. This will also lead to engine overheating.
Faulty radiator cap. The radiator cap is designed to hold a certain pressure in the coolant system. Most caps hold 8 - 12 PSI. This pressure raises the point in which the coolant will boil and maintains a stable system. If your cap does not hold pressure, then the car could overheat on hot days since the system never becomes pressurized.
Water pump failure. Most commonly you will hear a screeching noise and will be able to see coolant leaking from the front of the pump or under the car. Early signs are small spots of coolant under the car after being parked overnight and a strong coolant odor while driving.
Head gasket... have large amounts of white smoke flowing out of your exhaust? Could be a head gasket. The head gasket seals the cylinder head to the engine block and also seals the coolant passages. When this gasket fails coolant can enter the cylinder and it will be turned to vapor as the engine fires. Head gaskets most often fail after the engine has experienced an overheating situation. When super hot, the cylinder head can warp and allow the gasket to fail.
Preventive Maintenance:
Check all belts and hoses regularly. (at oil change is a good time)
Look out for coolant leaks underneath the car, they could be signs of trouble to come.
Change your coolant every 2 - 3 years depending on the manufactorers recommendations.
Inspect your radiator cap for deterioration of the rubber seal. Replace if you think it is worn. $5 - $10 is cheap insurance.
Have your coolant system flushed every 5 years. It gets all the corrosion which has built up out of the system.
What to discuss with your mechanic:
Let your mechanic know when your overheating problems occur. Overheating when idling points to a different problem than overheating at highway speeds.
Ask your mechanic if it's worth changing the timing belt or chain while he is replacing your water pump. Many times the timing belt turns the water pump so it has to be removed anyway to access the water pump.
WARNING: Never open your radiator when the engine is hot. The pressure in the system can cause hot coolant to splash out and burn you.
About The Author
Kevin Schappell maintains http://www.carbuyersclub.com where he gives advice on buying, selling, insurance, and financing. A mechanical engineer and car guy, Kevin has decided to spend his online time helping others learn about automobiles. To learn more about how your car works, Kevin has created http://www.mycarwizard.com.
kevin@schappell.com
This article was posted on December 23, 2004
by: Kevin Schappell
The purpose of the engine's cooling system is to remove excess heat from the engine, to keep the engine operating at its most efficient temperature, and to get the engine up to the correct temperature as soon as possible after starting. Ideally, the cooling system keeps the engine running at its most efficient temperature no matter what the operating conditions are.
As fuel is burned in the engine, about one-third of the energy in the fuel is converted into power. Another third goes out the exhaust pipe unused, and the remaining third becomes heat energy.
A cooling system of some kind is necessary in any internal combustion engine. If no cooling system were provided, parts would melt from the heat of the burning fuel, and the pistons would expand so much they could not move in the cylinders (called "seize").
The cooling system of a water-cooled engine consists of: the engine's water jacket, a thermostat, a water pump, a radiator and radiator cap, a cooling fan (electric or belt-driven), hoses, the heater core, and usually an expansion (overflow) tank.
Fuel burning engines produce enormous amounts of heat; temperatures can reach up to 4,000 degrees F when the air-fuel mixture burns. However, normal operating temperature is about 2,000 degrees F. The cooling system removes about one-third of the heat produced in the combustion chamber.
The exhaust system takes away much of the heat, but parts of the engine, such as the cylinder walls, pistons, and cylinder head, absorb large amounts of the heat. If a part of the engine gets too hot, the oil film fails to protect it. This lack of lubrication can ruin the engine.
On the other hand, if an engine runs at too low a temperature, it is inefficient, the oil gets dirty (adding wear and subtracting horsepower), deposits form, and fuel mileage is poor-- not to mention exhaust emissions! For these reasons, the cooling system is designed to stay out of the action until the engine is warmed up.
There are two types of cooling systems; liquid cooling and air cooling. Most auto engines are cooled by the liquid type; air cooling is used more frequently for airplanes, motorcycles and lawnmowers.
Liquid cooled engines have passages for the liquid, or coolant, through the cylinder block and head. The coolant has to have indirect contact with such engine parts as the combustion chamber, the cylinder walls, and the valve seats and guides. Running through the passages in the engine heats the coolant (it absorbs the heat from the engine parts), and going through the radiator cools it. After getting "cool" again in the radiator, the coolant comes back through the engine. This business continues as long as the engine is running, with the coolant absorbing and removing the engine's heat, and the radiator cooling the coolant.
A cooling system pressure tester is used to check the pressure in the cooling system, which allows the mechanic to determine if the system has any slow leaks. The leak can then be found and fixed before it causes a major problem.
The above information is directly from the Auto Insight program which you can buy online from AutoEducation.com.
Common Problems:
Let's look at the common problems cars have with the cooling system.
Broken hose. Hoses wear out and can leak. Once the coolant has left the system it can no longer cool the engine and it overheats.
Broken fan belt. The water pump is driven by the engine through a belt. If the belt breaks the water pump can not turn and coolant will not be circulated through the engine. This will also lead to engine overheating.
Faulty radiator cap. The radiator cap is designed to hold a certain pressure in the coolant system. Most caps hold 8 - 12 PSI. This pressure raises the point in which the coolant will boil and maintains a stable system. If your cap does not hold pressure, then the car could overheat on hot days since the system never becomes pressurized.
Water pump failure. Most commonly you will hear a screeching noise and will be able to see coolant leaking from the front of the pump or under the car. Early signs are small spots of coolant under the car after being parked overnight and a strong coolant odor while driving.
Head gasket... have large amounts of white smoke flowing out of your exhaust? Could be a head gasket. The head gasket seals the cylinder head to the engine block and also seals the coolant passages. When this gasket fails coolant can enter the cylinder and it will be turned to vapor as the engine fires. Head gaskets most often fail after the engine has experienced an overheating situation. When super hot, the cylinder head can warp and allow the gasket to fail.
Preventive Maintenance:
Check all belts and hoses regularly. (at oil change is a good time)
Look out for coolant leaks underneath the car, they could be signs of trouble to come.
Change your coolant every 2 - 3 years depending on the manufactorers recommendations.
Inspect your radiator cap for deterioration of the rubber seal. Replace if you think it is worn. $5 - $10 is cheap insurance.
Have your coolant system flushed every 5 years. It gets all the corrosion which has built up out of the system.
What to discuss with your mechanic:
Let your mechanic know when your overheating problems occur. Overheating when idling points to a different problem than overheating at highway speeds.
Ask your mechanic if it's worth changing the timing belt or chain while he is replacing your water pump. Many times the timing belt turns the water pump so it has to be removed anyway to access the water pump.
WARNING: Never open your radiator when the engine is hot. The pressure in the system can cause hot coolant to splash out and burn you.
About The Author
Kevin Schappell maintains http://www.carbuyersclub.com where he gives advice on buying, selling, insurance, and financing. A mechanical engineer and car guy, Kevin has decided to spend his online time helping others learn about automobiles. To learn more about how your car works, Kevin has created http://www.mycarwizard.com.
kevin@schappell.com
This article was posted on December 23, 2004
Abonați-vă la:
Postări (Atom)